Results 1 to 18 of 18

Thread: Parts and Advise Needed

  1. 06-26-2021, 11:35 PM #1
    SnailPony's Avatar
    SnailPony
    SnailPony is offline Registered User
    Join Date
    Feb 2017
    Posts
    118

    Parts and Advise Needed

    I recently purchased a D1SC and plan on running it in my coyote swapped fox. I am wanting to start gathering up some parts so I have everything I need come fall to get it installed on the car.

    Plan is to get it on the car and run 10-12psi. I currently have a 4.13 pulley but will buy whatever I need to get me in that range. I am currently running two tunes and switch from 93 and E85 as desired. I would like to still be able to do this so the injectors would need to be sized accordingly.

    I wanted to see what size / brand injectors you guys recommend?

    Also, I currently am running a TI450 fuel pump (I believe) purchased from Walter. How much power do you think this pump can support on 93 and E? Will I be safe at the 10-12# level? I’d like to keep this pump in the car is I can and not change it.


    Sent from my iPhone using Tapatalk
    Reply With Quote Reply With Quote
  2. 06-28-2021, 07:58 AM #2
    S281SC's Avatar
    S281SC
    S281SC is offline Registered User
    Join Date
    Jul 2015
    Posts
    452
    As far as the pump goes, i think it is good for about 700-750hp on e85. You might be close.


    Sent from my iPhone using Tapatalk
    #2 - 2020 DD Challenge List

    1997 Cobra - C heads, Cams, Sullivan intake, long tubes, homemade cai, 4.30, strange axles, e85, chromoly cage
    2000 Saleen S281SC - factory "stock"
    Reply With Quote Reply With Quote
  3. 06-28-2021, 08:21 AM #3
    Walter's Avatar
    Walter
    Walter is offline slow ride..
    Join Date
    Oct 2004
    Location
    Eastgate
    Posts
    3,367
    You will need a boost a pump to make that work on a single pump. Id1050 injectors is what i would recommend. But you should just spring for id1300. After all, you have an 8sec blower. As far as pulleys go, what diameter crank pulley are you running?
    Reply With Quote Reply With Quote
  4. 06-28-2021, 08:24 AM #4
    Walter's Avatar
    Walter
    Walter is offline slow ride..
    Join Date
    Oct 2004
    Location
    Eastgate
    Posts
    3,367
    Which procharger kit do you have? 11-14, 15-17, HO or stage 2?
    Reply With Quote Reply With Quote
  5. 06-28-2021, 09:06 PM #5
    SnailPony's Avatar
    SnailPony
    SnailPony is offline Registered User
    Join Date
    Feb 2017
    Posts
    118
    Quote Originally Posted by Walter View Post
    You will need a boost a pump to make that work on a single pump. Id1050 injectors is what i would recommend. But you should just spring for id1300. After all, you have an 8sec blower. As far as pulleys go, what diameter crank pulley are you running?
    Man, I’m not really a fan of boost a pumps... if that’s the case I’ll probably just swap lumps if I have too.

    Id1300 will get you into 4 digit power.. I’m looking for just over half that LOL. After all this is a gen 1 setup

    I do not have a complete kit as of yet. Still piecing it together. Brackets are next on the list to get (will come with lower pulley).


    Sent from my iPhone using Tapatalk
    Reply With Quote Reply With Quote
  6. 06-28-2021, 09:07 PM #6
    SnailPony's Avatar
    SnailPony
    SnailPony is offline Registered User
    Join Date
    Feb 2017
    Posts
    118
    Quote Originally Posted by Walter View Post
    You will need a boost a pump to make that work on a single pump. Id1050 injectors is what i would recommend. But you should just spring for id1300. After all, you have an 8sec blower. As far as pulleys go, what diameter crank pulley are you running?
    Quote Originally Posted by Walter View Post
    You will need a boost a pump to make that work on a single pump. Id1050 injectors is what i would recommend. But you should just spring for id1300. After all, you have an 8sec blower. As far as pulleys go, what diameter crank pulley are you running?
    Man, I’m not really a fan of boost a pumps... if that’s the case I’ll probably just swap lumps if I have too.

    Id1300 will get you into 4 digit power.. I’m looking for just over half that LOL. After all this is a gen 1 setup

    I do not have a complete kit as of yet. Still piecing it together. Brackets are next on the list to get (will come with lower pulley).


    Sent from my iPhone using Tapatalk
    Reply With Quote Reply With Quote
  7. 06-28-2021, 09:11 PM #7
    SnailPony's Avatar
    SnailPony
    SnailPony is offline Registered User
    Join Date
    Feb 2017
    Posts
    118
    Quote Originally Posted by Walter View Post
    Which procharger kit do you have? 11-14, 15-17, HO or stage 2?
    Im actually going to buy the “coyote swap” kit. Has a stag 2 intercooler with it.


    Sent from my iPhone using Tapatalk
    Reply With Quote Reply With Quote
  8. 06-29-2021, 12:10 AM #8
    Walter's Avatar
    Walter
    Walter is offline slow ride..
    Join Date
    Oct 2004
    Location
    Eastgate
    Posts
    3,367
    Ok, that's all i got for ya!
    Reply With Quote Reply With Quote
  9. 06-29-2021, 01:06 PM #9
    Maximus's Avatar
    Maximus
    Maximus is offline RIP Vinny
    Join Date
    Feb 2004
    Posts
    10,785
    Might as well get the Crank Snout support.
    http://stangbang.tripod.com/ Where all this began!
    http://stangbang.tripod.com/twisted/ Vinny
    1984 Mustang build @craig_btr on Instagram
    Reply With Quote Reply With Quote
  10. 06-29-2021, 01:16 PM #10
    Walter's Avatar
    Walter
    Walter is offline slow ride..
    Join Date
    Oct 2004
    Location
    Eastgate
    Posts
    3,367
    Crank support designed for 15-17 stg2, but could be modded to work.
    Reply With Quote Reply With Quote
  11. 06-30-2021, 11:11 PM #11
    SnailPony's Avatar
    SnailPony
    SnailPony is offline Registered User
    Join Date
    Feb 2017
    Posts
    118
    I know, not running a crank support on a pro charger coyote sounds bad LOL. Have heard of them ripping the snout out.

    Hoping low boost will be ok. I honestly don’t want a lot of power, just a little more than now lol.


    Sent from my iPhone using Tapatalk
    Reply With Quote Reply With Quote
  12. 07-01-2021, 06:17 AM #12
    draggin50's Avatar
    draggin50
    draggin50 is offline Registered User
    Join Date
    Jan 2009
    Location
    Hillsboro, Ohio
    Posts
    7,916
    Quote Originally Posted by SnailPony View Post
    I know, not running a crank support on a pro charger coyote sounds bad LOL. Have heard of them ripping the snout out.

    Hoping low boost will be ok. I honestly don’t want a lot of power, just a little more than now lol.


    Sent from my iPhone using Tapatalk
    That's what we all say!
    1992 Mustang LX Coupe, 302, PA C4 and On3 70mm.
    1993 Reef Blue hatch, 347, 3550, and a kit.
    1992 Gould GT project...
    Reply With Quote Reply With Quote
  13. 07-01-2021, 11:17 AM #13
    Walter's Avatar
    Walter
    Walter is offline slow ride..
    Join Date
    Oct 2004
    Location
    Eastgate
    Posts
    3,367
    Quote Originally Posted by SnailPony View Post
    I know, not running a crank support on a pro charger coyote sounds bad LOL. Have heard of them ripping the snout out.

    Hoping low boost will be ok. I honestly don’t want a lot of power, just a little more than now lol.


    Sent from my iPhone using Tapatalk
    Snout failures have happened on many different setups. Whipple, TT and NA. Ive been 9.01 at 150 on a stock gen2 with a p1sc at 3850lbs. You will be fine, but extra insurance is always nice.
    Reply With Quote Reply With Quote
  14. 07-01-2021, 11:46 AM #14
    Maximus's Avatar
    Maximus
    Maximus is offline RIP Vinny
    Join Date
    Feb 2004
    Posts
    10,785
    Quote Originally Posted by Walter View Post
    Snout failures have happened on many different setups. Whipple, TT and NA. Ive been 9.01 at 150 on a stock gen2 with a p1sc at 3850lbs. You will be fine, but extra insurance is always nice.
    TT and NA? Well thats just shitty.
    http://stangbang.tripod.com/ Where all this began!
    http://stangbang.tripod.com/twisted/ Vinny
    1984 Mustang build @craig_btr on Instagram
    Reply With Quote Reply With Quote
  15. 07-02-2021, 01:19 AM #15
    Walter's Avatar
    Walter
    Walter is offline slow ride..
    Join Date
    Oct 2004
    Location
    Eastgate
    Posts
    3,367
    Parts break, it is what it is.
    Reply With Quote Reply With Quote
  16. 07-06-2021, 09:52 PM #16
    SnailPony's Avatar
    SnailPony
    SnailPony is offline Registered User
    Join Date
    Feb 2017
    Posts
    118
    Quote Originally Posted by draggin50 View Post
    That's what we all say!
    Lol well it is still a gen 1 setup. I don’t want to push it too much.


    Sent from my iPhone using Tapatalk
    Reply With Quote Reply With Quote
  17. 07-06-2021, 11:38 PM #17
    Maximus's Avatar
    Maximus
    Maximus is offline RIP Vinny
    Join Date
    Feb 2004
    Posts
    10,785
    We have all said that at one point…right before we add another pound or two of boost!
    http://stangbang.tripod.com/ Where all this began!
    http://stangbang.tripod.com/twisted/ Vinny
    1984 Mustang build @craig_btr on Instagram
    Reply With Quote Reply With Quote
  18. 07-07-2021, 07:03 PM #18
    SnailPony's Avatar
    SnailPony
    SnailPony is offline Registered User
    Join Date
    Feb 2017
    Posts
    118
    Anyone have some 1000-1200cc injectors laying around for a coyote?


    Sent from my iPhone using Tapatalk
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules