Misc Mustang parts

[draggin50]

I have several parts cars that I have stripped and I have all kinds of fox stuff laying around. Wife is about to lose her shit if I don't start selling stuff or build a fence!

2 sets of 87-93 V8 spindles/brakes- $100 a set with rotors and calipers
Mint black dash- $150
Nice set of black door panels. Do not have the map pockets- $75
LX wing- $20
GT wing- $20
Whole cowl panels- $100 each. I have 3. These are cut off and will need the spot welds drilled off to be installed on a car.
Complete black interior. Drivers seat is trash but everything else is decent. Headliner, visors, dash, console, all plastics, seats, and hatch carpet. If you want the carpet Ill throw that in too. $600
Grey quarter plastic- $25
Holley heads, 1.94/1.54 I think. Screw in studs $550
Set of pony wheels with tires- $150
8.8 rear end with 3.73 gear- $150
Power Doors (have a few) $25 each
Mint 86 black console and armrest- $200
86 fog light bar with lights- $150
Complete T5 swap (tranny, bell, clutch, cable, pedals, stock shifter)- $500

May sell the 86 I just picked up from Egbert. Real nice shell and will have a stock K member and V8 spindles and brakes, Tokico blue struts, 8.8 with 3.55 gear, and boxes of parts... I can throw in some 87-93 grey interior for a little more. Has newer quarter glass in it. Body is real nice. Under the hood has been smoothed and in primer. $1200

If you are looking for anything special, hit me up. I have complete cars that I will be parting out.

[mustangboy]

You happen to have a good guage hood for a 90-93? The tabs are cracked on mine

[draggin50]

I'll check and see when i get home. I think I do.

[redfirepearlgt]

NO 15-17 parts....Rats.

[blue5.8]

I’ll take the black door panels also looking for a bunch of other parts for my 89 coupe I will PM you a list

[draggin50]

Text me a list 937-944-3547

[draggin50]

Got a pile of parts that need to go! 4 junk ones sitting here that are being picked apart. Let me know what you need.

[mustangboy]

Any luck with that gauge hood?

Sent from my Pixel 3 XL using Tapatalk

[92sc4v]

Do you have any power window switches

[draggin50]

Yeah I probably have a couple sets here. Ill pull some out tomorrow.

[draggin50]

Any luck with that gauge hood?

Sent from my Pixel 3 XL using Tapatalk

Ill check tomorrow. I forgot all about ya. Sorry about that!

[92sc4v]

Ok let me know when I can pick them up
I only live about 15 mins from you

[draggin50]

Any luck with that gauge hood?

Sent from my Pixel 3 XL using Tapatalk

I didn't find a good gauge hood.

[mustangboy]

I didn't find a good gauge hood.Ok thanks for looking

Sent from my Pixel 3 XL using Tapatalk

[draggin50]

Ok let me know when I can pick them up
I only live about 15 mins from you

Hey give me a call this weekend for the switches. I should be around both days. 937-944-3547

[SnailPony]

I’m looking for a stock fuel filter bracket, have one?


Sent from my iPhone using Tapatalk

[draggin50]

Im sure I do. Ill run out and check and make sure the ones I have are decent.

[SnailPony]

https://uploads.tapatalk-cdn.com/20200107/1ef75dba8d4603253c5be10f77c72536.jpg

Do you happen to have a hvac panel for a 90? I have seemed to misplace mine years ago


Sent from my iPhone using Tapatalk

[draggin50]

Ill take a look tonight. I think I have a couple.

[draggin50]

https://uploads.tapatalk-cdn.com/20200107/1ef75dba8d4603253c5be10f77c72536.jpg

Do you happen to have a hvac panel for a 90? I have seemed to misplace mine years ago


Sent from my iPhone using Tapatalk

I forgot all about looking for this. Ill get out there tomorrow and check.

[draggin50]

Stuff I still have to sell....

1 set of 87-93 V8 spindles/brakes- $100 with rotors and calipers
GT wing- $20
Whole cowl panel- $100
Mint 86 black console and armrest- $200
1986 Mustang LX. Real nice shell with a nice set of manual doors and will have a stock K member, V8 spindles and brakes, Tokico blue struts, 8.8 with 3.55 gear, and boxes of parts... I can throw in some 87-93 grey interior for a little more. Has newer quarter glass in it. Body is real nice. Under the hood has been smoothed and in primer. $1200
Ported truck lower and Systemax upper- $400
BBK 70mm TB and EGR plate- $150
12-200 coil over springs- $50
DSS main girdle and windage tray with studs and hardware- $200
C&L 73mm mass air meter for 19lb injectors- $50
Complete 5.0 with pulleys and AC delete with an F cam and Explorer GT40 intake- $700. Have a video of it running right before it was pulled.
Complete, fresh RMVB C4 with a DirtyDog converter and a 50oz flexplate. Worked good behind a turbo and a small blower. $650. Will throw in a B&M Hammer shifter for another $100.

[draggin50]

Still have some parts left...

1 set of 87-93 V8 spindles/brakes- $100 with rotors and calipers
GT wing- $20
Whole cowl panel- $100
Mint 86 black console and armrest- $200
BBK 70mm TB and EGR plate- $150
C&L 73mm mass air meter for 19lb injectors- $50
Complete 5.0 with pulleys and AC delete with an F cam and Explorer GT40 intake- $700. Have a video of it running right before it was pulled.
B&M Hammer shifter for C4- $100.
24lb injectors and mass air meter- $125
fox airbag steering column- $50

[draggin50]

Throttle body and EGR plate is gone...

Still have the rest.

[draggin50]

Still have a lot of parts to sell...

1 set of 87-93 V8 spindles/brakes- $100 with rotors and calipers
GT wing- $20
LX wing $20
Decent hatch. Has holes for the old 3 piece wing. Good glass- $50
Whole cowl panel- $100
Nice passenger side frame rail and strut tower- $75
Hatch Quarters- $75 each
C&L 73mm mass air meter for 19lb injectors- $50
Complete 5.0 with pulleys and AC delete with an F cam and Explorer GT40 intake- $700. Have a video of it running right before it was pulled.
B&M Hammer shifter for C4- $100.
Grey interior parts (Quarter plastics, dash, console, kick panels- $100
Holley Systemax cam. I think this is the older 107 cam. In good shape. $50