Gopro 9.94 run from Edgewater Saturday

[Dtony]

Heres the vid of a pass I had Saturday at Edgewater. The pass was 9.94 @ 137.48 with a 1.43 60' .

http://www.youtube.com/watch?v=ml3MheTem3c&feature=player_embedded#!

[jktruckin06]

Nice run. Those cameras are neat

[sprayn93coupe]

Nice pass!

[Maximus]

Streetcar getting it done! Kick Ass!!:bigthumb

[plated]

you make it look so easy,impressive.nice work

[331lx]

nice run man

[Dtony]

Thanks guys. The new suspension setup seems to work real well.

[plated]

what did it 60? stock converter? stock driveshaft? spring shock combo?if u dont mind me asking

[redfirepearlgt]

sweet run. time for a chute!?!?!?

[USMCPONY]

What's all done to the car?

[kennebellcobra]

Those cameras are cool! Nice pass!

[2Fast4You]

Way to get that thing off the line, car is moving.

[Walter]

sweet run. time for a chute!?!?!?

Chute is for 150mph or faster.

[m347]

Nice run! That is moving. Did you go back on Sunday or did they open?

[Dtony]

what did it 60? stock converter? stock driveshaft? spring shock combo?if u dont mind me asking

I will post the time slip for the incrementals.

I use a Circle D 3C converter that stalls to 3600, Axle Exchange 4" alum drive shaft, BMR 165 lb rate front springs on stock struts, H&R rear 1" drop springs and Lake wood old school 50/50 shocks.


What's all done to the car?

The car has: a stock Boss short block, Boss intake, Boss valve springs, billet oil pump gears (because we really rev this thing), Kooks long tubes and off road x pipe, Vortech V3 Si with one pulley size drop (12 lbs of boost), Stock trans with a converter, 3.31 rear gears with stock differential with carbon clutches. Also quite a bit of suspension work done.


sweet run. time for a chute!?!?!?

I am getting ready to get the roll bar updated to an 8.50 cage and considered a chute in case I step it up. But in reality I want to keep this like a stock appearing car from the outside.

It's pretty unassuming when you see it.


Nice run! That is moving. Did you go back on Sunday or did they open?

I didnt make it out, E2O basically told me to not bring it back out until certified so I thought there wasn't much point. They were cool this time tho, they let me continue running, the last 2 times I was told to stop or slow down. It was the 3rd time they have told me that. :D

[Dtony]

Thanks for the compliments guys. It's a fun ride and I am looking forward to meeting more forum peeps this summer.


http://i244.photobucket.com/albums/gg2/dodgetony/E2O3.jpg
Picture by Aries Xcecutioner

http://i244.photobucket.com/albums/gg2/dodgetony/994at13748.jpg

[maverick]

Nice! :bigthumb

[m347]

You could lift a little early but the 1/8 mile cut off for a chassis cert is 6.40. They might leave you alone on that though.

[corey331]

Nice pass. I know when I was taking vids of my boat with the GoPro, if you use the waterproof case, you won't get anywhere near the wind noise, but you still get all the motor noise. Just an FYI, since I know most of us would rather hear that motor wingin at 143mph rather than the wind!!

[Blwn Pony]

Nice! damn I want a new 5.0 so bad

[90fastgt]

Nice run!!

[Dtony]

Nice pass. I know when I was taking vids of my boat with the GoPro, if you use the waterproof case, you won't get anywhere near the wind noise, but you still get all the motor noise. Just an FYI, since I know most of us would rather hear that motor wingin at 143mph rather than the wind!!

Thanks for the heads up. I will give it a shot. I had no idea the wind noise would be as bad as it was.

[cobraman302]

Thanks for the heads up. I will give it a shot. I had no idea the wind noise would be as bad as it was.

I heard the duct tape on the mic does the truck as well.

Good running car. Just curious, what do these cars run on a simple 10lb blower in stock form?

[Dtony]

I heard the duct tape on the mic does the truck as well.

Good running car. Just curious, what do these cars run on a simple 10lb blower in stock form?

With an auto most run mid tens with blower only.