View Full Version : EFI Spyder and a stock hood
SCHMUCKINGHAM
12-11-2011, 11:10 AM
I bought Kenny's ( MustangBoy) old EFI Spyder/ modified Performer intake and while assembling everything on the stand I dont think this elbow will fit under my stock hood but I wanted to see what others are running or using to fit it under a stock hood. I already have ES mounts but the K member is stock.
89notch
12-11-2011, 11:31 AM
http://www.intakeelbows.com/mustang.htm
Might need one of these
Goober
12-11-2011, 12:48 PM
http://www.intakeelbows.com/mustang.htm
Might need one of these
If it'll fit a 9.5" Super Vic under a stock Fox hood than it should clear either with a stock hood. That Spyder EFI was a Vic Jr., right?
I'm hoping it'll clear an 8.2" Super Vic on the 94 with a 1" setback and 1.5" cowl
SCHMUCKINGHAM
12-12-2011, 12:40 PM
If it'll fit a 9.5" Super Vic under a stock Fox hood than it should clear either with a stock hood. That Spyder EFI was a Vic Jr., right?
I'm hoping it'll clear an 8.2" Super Vic on the 94 with a 1" setback and 1.5" cowl
Honestly I cant remember, it was a carb intake modified to EFI
SCHMUCKINGHAM
12-12-2011, 12:41 PM
http://www.intakeelbows.com/mustang.htm
Might need one of these
Holy looks expensive haha
Timido
12-12-2011, 07:01 PM
If it was a 302 Intake from Kenny it should be a Victor Jr.
mustangboy
12-12-2011, 07:54 PM
It would not fit under a stock hood on my car in fact I have a hole cut in my cowl hood to fit but I also had a 1" spacer on mine as well. Without the spacer it should have cleared the hood but not sure if it would have cleared the fuel rails. You could also look into the the edelbrock elbows I think they are approx $120 vs $225 for the sheetmetal ones. Good luck
SCHMUCKINGHAM
12-13-2011, 11:51 AM
The EFI Spyder clears the rails without a spacer just fine but I dont think it will clear the factory hood at all.
mustangboy
12-13-2011, 12:59 PM
Here is the link to Edelbrocks site so you can see what they have that may work for you. Surely one of the short ones will fit under a stock hood
http://www.edelbrock.com/automotive_new/mc/efi/intake_elbows.shtml
SCHMUCKINGHAM
12-13-2011, 01:03 PM
Here is the link to Edelbrocks site so you can see what they have that may work for you. Surely one of the short ones will fit under a stock hood
http://www.edelbrock.com/automotive_new/mc/efi/intake_elbows.shtml
But will it clear the rails, thats the 150 dollar question LOL
bennyboy
12-16-2011, 08:53 AM
i have one on my 95 it clears rails with no spacer but i have a cobra r hood
Goober
12-16-2011, 06:38 PM
i have one on my 95 it clears rails with no spacer but i have a cobra r hood
More info please, such as what hood, intake manifold, block and mounts?
SCHMUCKINGHAM
12-17-2011, 09:46 AM
More info please, such as what hood, intake manifold, block and mounts?
You read my mind
TONYT
12-21-2011, 01:49 PM
i had that prob. so i took mine to my mach shop and had it cut down to fit
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.