393W For Sale

[NXcoupe]

I have a complete intake to pan 393 with about 1500 miles or so on it. Has a probe cast steel crank, H beam probe rods and CP forged flat top pistons with a valve relief large enough that it accommodates both twisted wedge and inline heads, .030 over, torque plate honed, balanced to 28 oz, decked, has stage 3 tfs cam, crane retro roller lifters, TFS pushrods, TFS Twisted Wedge heads TEA ported stage 3 renegade titanium retainers, new springs, 10 degree locks, Felpro multilayer gaskets, TFS R intake(no portwork), FRPP swap pan, new timing cover, water pump, etc, TFS valve covers, TFS rocker arms 1.6 7/16" stud(These are the crane gold ones, not the new scorpions), billet gear timing set, all arp hardware, girdle and studs, melling oil pump, ARP driveshaft, PP balancer, Oreilly rebuilt TFI distributor with steel gear.
Asking 4500 obo, can hear run, made 470 rwhp on E85 with more in it with some minor changes in combo(port intake, etc). Just tossing this out there in case someone is wanting it complete before I start tearing it down. A spyder intake or portwork with a box would put this over 500 rwhp, it made 470 at 5400 rpms.

[Goober]

If this ends up being a part out, I have dibs on those heads!









Seriously, dibs.








Those heads.

[Jake]

are you looking for offers or did you have a price in mind?

[NXcoupe]

If this ends up being a part out, I have dibs on those heads!

Seriously, dibs.

Those heads.

I seriously doubt the engine will sell, but I always give someone a chance at a deal before I break it up. I'll keep you in mind when I get to this. Should be sometime next week when I pull it and break it down. I'll get pics of everything as I pull it as well. Figure this stuff will get a week on here, then I'll move onto the bigger boards and move it quickly.

[mad max]

Poor barney.

[NXcoupe]

are you looking for offers or did you have a price in mind?


Asking 4500
That's the price. Keep in mind when I part it, I will get substantially more for it.

[NXcoupe]

Poor barney.

He pissed me off one too many times.

[Jake]

....whoops. thanks.

[bronzeLX]

You guys need to take a look at it before it comes out, motor sounds great.

[Goober]

I'll talk to you about them at the christmas party tomorrow.

[NXcoupe]

You guys need to take a look at it before it comes out, motor sounds great.

Thanks! Loved it, it was frickin stupid fast, a blast to drive, but when the heater core took a dump it was just the last straw for me and I'm done with it. I just don't need another car needing worked on so I am just going to concentrate on my race car and getting it deeper into the 9's.

[blown96cobra]

very nice strong motor, ive ridden in the car a few times and runs/sounds wicked!

[2Fast4You]

I wish I had money to buy that bad boy, I know it is well worth every dollar your asking for it. GLWS Mike, I hope to stop by tomorrow.

[NXcoupe]

Be good to see you. I could fire it up if you wanna hear it.
I want to throw it out there too, that I will do a layaway on this as well. That goes for any used parts I sell. As long as it's cash and you stick to the payments, it's yours.

[cyah92]

This is what i need damn thats a good price

[cyah92]

This is what i need damn thats a good price

[NXcoupe]

Ok, about one more week before I rip it out and start selling off the parts, got someone putting dibs on the heads, got another interested in the cam, so it's tempting to just yank and part it. Let me know if anyone wants to work out something on it, not willing to give it away.

[Goober]

PM me what you plan on asking for the heads so I can prepare the wife...

[NXcoupe]

Sent...........

[Goober]

And returned

[NXcoupe]

Just a little while longer before it comes out.....

[2Fast4You]

MIke,
If this engine does not sell complete, I am interested in the short block. Let me know what you are looking to get just for it.

[2Fast4You]

What headers were you running on it?
May also interested in the headers if you are parting w/ those as well.

[NXcoupe]

Yep, exhaust is going as well. It is a set of custom headers from Accufab, they are a mid length design and have V band flanges to a 3" exhaust, H pipe, to 3" bullets. sounds incredible. Headers are 1 3/4". Cleared everything nicely even with a stock K member and a scattershield.
Deal pending on the engine, I'll know Sunday............

[NXcoupe]

Sold pending final payment.

[NXcoupe]

Sold! Thanks Cyah!