Flaming87lx
09-01-2010, 11:37 PM
.030 1969 351w
assy is balanced and blueprinted 28oz
TRW domed forged pistons, .210 dome
Eagle H-beam rods
Eagle 4340 steel crank
HV Oil pump
Fox racing oil pan
SFI Flexplate
Crane solid flat or hyd flat lifters can used 3200-6800 (specs below)
Windsor Sr. Heads 2.05/1.60 valves, 200cc intake runners (used) intake side has been gasket matched 64cc combustion chambers
Harland Sharp 1.6 roller rockers (used)
$3800 in parts and I'm guessing close to $1000 in machine work and assembly.
Shortblock has never been fired. Motor is right at 12-1 compression. The motor was spec out to carry a 4000lb car 10.90's with a super victor and I'm guessing a 950 or 1050 carb.
*****Needs, intake, push rods, lifters, timing chain and gears, dist, and carb to complete....*****
I also have a (used) Ultradyne solid roller cam and lifters, .668 lift, 3500-7500 range. You would have to change valve springs tho. $600 setup
cam specs-
Cam Style Mechanical flat tappet
Basic Operating RPM Range 3,400-6,800
Intake Duration at 050 inch Lift 244
Exhaust Duration at 050 inch Lift 252
Duration at 050 inch Lift 244 int./252 exh.
Advertised Intake Duration 280
Advertised Exhaust Duration 288
Advertised Duration 280 int./288 exh.
Intake Valve Lift with Factory Rocker Arm Ratio 0.553 in.
Exhaust Valve Lift with Factory Rocker Arm Ratio 0.572 in.
Valve Lift with Factory Rocker Arm Ratio 0.553 int./0.572 exh.
Lobe Separation (degrees) 108
Intake Valve Lash 0.026 in.
Exhaust Valve Lash 0.026 in.
Computer-Controlled Compatible No
Grind Number F-280-2
I want to trade for similar setup that runs on pump gas!!!!
Call or text 765-541-0577
http://i249.photobucket.com/albums/gg237/mustang398/c93571.jpg
http://i249.photobucket.com/albums/gg237/mustang398/c93574.jpg
http://i249.photobucket.com/albums/gg237/mustang398/c93573.jpg
http://i249.photobucket.com/albums/gg237/mustang398/c93572.jpg
http://i249.photobucket.com/albums/gg237/mustang398/heads.jpg
assy is balanced and blueprinted 28oz
TRW domed forged pistons, .210 dome
Eagle H-beam rods
Eagle 4340 steel crank
HV Oil pump
Fox racing oil pan
SFI Flexplate
Crane solid flat or hyd flat lifters can used 3200-6800 (specs below)
Windsor Sr. Heads 2.05/1.60 valves, 200cc intake runners (used) intake side has been gasket matched 64cc combustion chambers
Harland Sharp 1.6 roller rockers (used)
$3800 in parts and I'm guessing close to $1000 in machine work and assembly.
Shortblock has never been fired. Motor is right at 12-1 compression. The motor was spec out to carry a 4000lb car 10.90's with a super victor and I'm guessing a 950 or 1050 carb.
*****Needs, intake, push rods, lifters, timing chain and gears, dist, and carb to complete....*****
I also have a (used) Ultradyne solid roller cam and lifters, .668 lift, 3500-7500 range. You would have to change valve springs tho. $600 setup
cam specs-
Cam Style Mechanical flat tappet
Basic Operating RPM Range 3,400-6,800
Intake Duration at 050 inch Lift 244
Exhaust Duration at 050 inch Lift 252
Duration at 050 inch Lift 244 int./252 exh.
Advertised Intake Duration 280
Advertised Exhaust Duration 288
Advertised Duration 280 int./288 exh.
Intake Valve Lift with Factory Rocker Arm Ratio 0.553 in.
Exhaust Valve Lift with Factory Rocker Arm Ratio 0.572 in.
Valve Lift with Factory Rocker Arm Ratio 0.553 int./0.572 exh.
Lobe Separation (degrees) 108
Intake Valve Lash 0.026 in.
Exhaust Valve Lash 0.026 in.
Computer-Controlled Compatible No
Grind Number F-280-2
I want to trade for similar setup that runs on pump gas!!!!
Call or text 765-541-0577
http://i249.photobucket.com/albums/gg237/mustang398/c93571.jpg
http://i249.photobucket.com/albums/gg237/mustang398/c93574.jpg
http://i249.photobucket.com/albums/gg237/mustang398/c93573.jpg
http://i249.photobucket.com/albums/gg237/mustang398/c93572.jpg
http://i249.photobucket.com/albums/gg237/mustang398/heads.jpg