SCHMUCKINGHAM
06-10-2010, 04:39 PM
I have a complete setup from front to back for a Fox, all you need is some fab and your done.
At the front end is a brand spankin new set of Accufab longtube I havent even installed yet. 1.75in primary tubes with a 3in collector setup for stock or Twisted wedge heads and a manual trans on an 8.2 deck. Also I just got them back from ceramic coating, its a ceramic coat with a top coat then a clear. I literally just picked these up from the coater today and they look awesome. Between the Headers, H pipe, and coating I have 950 bucks in this setup, Not including the dumps and mufflers.
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture144.jpg
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture142.jpg
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture141.jpg
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture138.jpg
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture137.jpg
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture145.jpg
The H pipe is a slip fit 3in that needs welded in the center, I have the band clamps for the exhaust and as you can see it hasnt been installed either. It is made of mild steel and will rust but I was going to hit it with some high heat piant.
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture131.jpg
All the hardware is included even the mufflers, which are Magnaflow 3in in and 3in outs with an offset side and a center opposite. Theya re used and have had hangers cut off but they looks good. They are the polished ones. The dumps and clamps are also new.
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture132.jpg
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture134.jpg
I have over a grand in all this but Ill sell everything complete for $800 total plus shipping. A this point I dont want to part things out and trades depend on what you have.
At the front end is a brand spankin new set of Accufab longtube I havent even installed yet. 1.75in primary tubes with a 3in collector setup for stock or Twisted wedge heads and a manual trans on an 8.2 deck. Also I just got them back from ceramic coating, its a ceramic coat with a top coat then a clear. I literally just picked these up from the coater today and they look awesome. Between the Headers, H pipe, and coating I have 950 bucks in this setup, Not including the dumps and mufflers.
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture144.jpg
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture142.jpg
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture141.jpg
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture138.jpg
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture137.jpg
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture145.jpg
The H pipe is a slip fit 3in that needs welded in the center, I have the band clamps for the exhaust and as you can see it hasnt been installed either. It is made of mild steel and will rust but I was going to hit it with some high heat piant.
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture131.jpg
All the hardware is included even the mufflers, which are Magnaflow 3in in and 3in outs with an offset side and a center opposite. Theya re used and have had hangers cut off but they looks good. They are the polished ones. The dumps and clamps are also new.
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture132.jpg
http://img.photobucket.com/albums/v226/Schmuckingham/For%20sale%20stuff/Picture134.jpg
I have over a grand in all this but Ill sell everything complete for $800 total plus shipping. A this point I dont want to part things out and trades depend on what you have.