Paul408Notch
01-03-2010, 08:51 PM
This is the AEM EMS that's currently in my car. The thing is the most feature-packed ECU you can buy for a Fox, and can do darn near anything you want it to. I'm just selling it because I'm a gadget freak, and I want to move on to something else.
AEM EMS pn 30-1400. Plug-and-Play ECU for Fox Mustangs.
Controls all aspects of the following that you can possibly think of, using a windows-based PC for tuning.
Can run MAF or Speed-Density.
Fuel: Base, accel, decel, idle, limiters, 2-steps, retards, traction control.
Spark: Same as above.
Boost: Will control boost with 2 solenoids. Instant, ramp, per-gear.
Wideband Control
Inputs and Outputs for fans, nitrous, seat massagers, whatever you need to control.
My car made 385hp/406tq and I was barely making this thing sweat at all. The only thing it won't do is control low-impedance injectors, though it can run those with some minor wiring changes.
Installs in minutes using Plug & Play technology—no wiring necessary!
Start-up calibrations included
Live help window eases tuning process.
Set-up Wizard creates a custom base map for your car
System is fully enabled—Never pay for upgrades!
Free software updates on aempower.com
Uses all the factory sensors.
Runs on Windows™ compatible software.
Fuel table automapping.
Programmable traction control.
Onboard 512kb datalogger.
Up to 10 cylinder sequential fuel injection .
16 general-purpose outputs.
7 definable switch inputs.
Electronic boost control.
Soft cut rev limiters .
Two step launch control.
Wet or dry nitrous control .
Definable knock control.
Full idle control.
4 EGT inputs with fuel control .
16/32 hybrid high speed processor.
Includes ECU, Cable, CD, Box, (Over 1600 from Jeg's) and I'm including the 3.5 BAR AEM MAP sensor as well, (which is about $160 by itself. It's a super-high-quality screw-in sensor). And depending on what we work out, I may be willing to help with your installation, initial start-up, and tuning.
$1300 with a couple of hours of assistance. All negotiable.
http://i244.photobucket.com/albums/gg31/efipaul/ForSale/AEM1.jpg
AEM EMS pn 30-1400. Plug-and-Play ECU for Fox Mustangs.
Controls all aspects of the following that you can possibly think of, using a windows-based PC for tuning.
Can run MAF or Speed-Density.
Fuel: Base, accel, decel, idle, limiters, 2-steps, retards, traction control.
Spark: Same as above.
Boost: Will control boost with 2 solenoids. Instant, ramp, per-gear.
Wideband Control
Inputs and Outputs for fans, nitrous, seat massagers, whatever you need to control.
My car made 385hp/406tq and I was barely making this thing sweat at all. The only thing it won't do is control low-impedance injectors, though it can run those with some minor wiring changes.
Installs in minutes using Plug & Play technology—no wiring necessary!
Start-up calibrations included
Live help window eases tuning process.
Set-up Wizard creates a custom base map for your car
System is fully enabled—Never pay for upgrades!
Free software updates on aempower.com
Uses all the factory sensors.
Runs on Windows™ compatible software.
Fuel table automapping.
Programmable traction control.
Onboard 512kb datalogger.
Up to 10 cylinder sequential fuel injection .
16 general-purpose outputs.
7 definable switch inputs.
Electronic boost control.
Soft cut rev limiters .
Two step launch control.
Wet or dry nitrous control .
Definable knock control.
Full idle control.
4 EGT inputs with fuel control .
16/32 hybrid high speed processor.
Includes ECU, Cable, CD, Box, (Over 1600 from Jeg's) and I'm including the 3.5 BAR AEM MAP sensor as well, (which is about $160 by itself. It's a super-high-quality screw-in sensor). And depending on what we work out, I may be willing to help with your installation, initial start-up, and tuning.
$1300 with a couple of hours of assistance. All negotiable.
http://i244.photobucket.com/albums/gg31/efipaul/ForSale/AEM1.jpg