black90lx
07-30-2009, 07:38 PM
1988 mustang gt. the car was repainted a couple years ago but the guy didn't prep the ground effects right and it is starting to chip off. it will need to be touched up from the trim down. it has over $15,000 in performance parts on it. it has tinted windows and it is not lowered any more, it sits at the factory height. it is mechanically sound and runs great. i drive this car to and from the track(45 min away) and has never been trailered.
MOTOR
-holley systemax 2 intake with 1" spacer
-30lb ford motorsport red top injectors w/ matching meter
-trickflow twisted wedge aluminum heads milled 40 thousand's
-trickflow 1.6 roller rockers
-trickflow 6.65 1 piece hardened pushrods
-trickflow valve covers
-70 mm bbk throttle body and spacer
-mac chrome fender well cold air kit
-stock shortblock
-NX wet nitrous kit with shark nozzle and big solenoids w/purge
-fuel pressure safety switch
-ashtray switch panel for the nitrous
-automatic bottle heater set at 1000psi
-bottle pressure gauge on bottle
-be cool aluminum radiator
-black magic electric fan
-bbk equal length shorty headers
-bbk h-pipe
-mac mufflers
-converted to mass air
-a9l computer
-energy suspension poly motor mounts
-arp head studs
-arp oil pump shaft
-pro products sfi fluid dampner
-302 forged internals
-trickflow stage 1 cam
-fresh bottom end with around 2000 miles
TRANNY
-pan filled c-4
-kevlar bands
-red clutches
-hardened input shaft
-performance automatic servo
-custom built TCI convertor. stalls at 3500 on the foot brake
-tci flex plate
-tranny cooler with steel braided lines and an-fittings
-locking dipstick
-tci manual reverse valve body
-b&m pro stick shifter
.................................................. .................................................. .........
-aluminum drive shaft
-ford motorsport 3.73 gears
-converted to 5 lug with sn95 front breaks and rear ranger axel's
-weld pro stars front (15x3.5) and rear(15x8)
-27x10.5 hoosier quick time pro's in the rear
-lakewood 90/10 front drag shocks
-4 cylinder front springs
-gt rear springs
-bbk upper and lower rear control arms
-190lph intank fuel pump
-t-rex 255lph boost a pump
-cervini's 4 inch cowel hood
-cobra grill insert
-battery in hatch
-msd 6btm ignition box
-msd coil
-msd distributor
-msd plug wires
-msd digital window switch
-msd 2 step
-3g alternator upgrade from a 94-95 mustang
-converted to 140 mph speedometer
2 5/8 autometer pro comp gauges
-volt
-monster tach
-water temp
-oil pressure
-boost/vac
-fuel pressure
-dash and pillar pod's
i'm sure there is some more other things i am forgeting. i also have a set of moser 31 spline 5 lug axles with long studs, fms 31 spline carrier and 3.55 fms gear to go with the car
if you have any questions give me a call anytime, 937-751-2970, scott
MOTOR
-holley systemax 2 intake with 1" spacer
-30lb ford motorsport red top injectors w/ matching meter
-trickflow twisted wedge aluminum heads milled 40 thousand's
-trickflow 1.6 roller rockers
-trickflow 6.65 1 piece hardened pushrods
-trickflow valve covers
-70 mm bbk throttle body and spacer
-mac chrome fender well cold air kit
-stock shortblock
-NX wet nitrous kit with shark nozzle and big solenoids w/purge
-fuel pressure safety switch
-ashtray switch panel for the nitrous
-automatic bottle heater set at 1000psi
-bottle pressure gauge on bottle
-be cool aluminum radiator
-black magic electric fan
-bbk equal length shorty headers
-bbk h-pipe
-mac mufflers
-converted to mass air
-a9l computer
-energy suspension poly motor mounts
-arp head studs
-arp oil pump shaft
-pro products sfi fluid dampner
-302 forged internals
-trickflow stage 1 cam
-fresh bottom end with around 2000 miles
TRANNY
-pan filled c-4
-kevlar bands
-red clutches
-hardened input shaft
-performance automatic servo
-custom built TCI convertor. stalls at 3500 on the foot brake
-tci flex plate
-tranny cooler with steel braided lines and an-fittings
-locking dipstick
-tci manual reverse valve body
-b&m pro stick shifter
.................................................. .................................................. .........
-aluminum drive shaft
-ford motorsport 3.73 gears
-converted to 5 lug with sn95 front breaks and rear ranger axel's
-weld pro stars front (15x3.5) and rear(15x8)
-27x10.5 hoosier quick time pro's in the rear
-lakewood 90/10 front drag shocks
-4 cylinder front springs
-gt rear springs
-bbk upper and lower rear control arms
-190lph intank fuel pump
-t-rex 255lph boost a pump
-cervini's 4 inch cowel hood
-cobra grill insert
-battery in hatch
-msd 6btm ignition box
-msd coil
-msd distributor
-msd plug wires
-msd digital window switch
-msd 2 step
-3g alternator upgrade from a 94-95 mustang
-converted to 140 mph speedometer
2 5/8 autometer pro comp gauges
-volt
-monster tach
-water temp
-oil pressure
-boost/vac
-fuel pressure
-dash and pillar pod's
i'm sure there is some more other things i am forgeting. i also have a set of moser 31 spline 5 lug axles with long studs, fms 31 spline carrier and 3.55 fms gear to go with the car
if you have any questions give me a call anytime, 937-751-2970, scott