bbfstanger
07-06-2009, 08:43 PM
i hate to do it but im gonna see if anyone is interested in my engine.
have almost everything to complete it.
DOVE blk soniced,cleaned,billet splayed 4bolt caps,canton main girdle,arp bolts,has been alignbored,needs cyl's bored and honed and decked,have new cam bearings for it too.
new .080 over diamond flattop pistons with upgraded pins.
new .080 over totalseal file fit plasmamoly rings
new grp alum rods 6.800 long.
used crankshaft specialties billet crank 4.5 stroke fresh 20/20 grind has shorter boss snout,has been magged all is good. crank cost $2500 new
new fms damper,i have the short sleeve for the boss snout too.
canton windage tray bolts to the girdle,canton pan, pickup and dipstick for a foxbody.
new custom grind nos cam 289-312.050 825 lift-814. 115sep
nice used set of crane roller lifters,my friend had these so i know theyre good and how long they were used.
fms blue roller rockers and locks
old style fms A-heads ported flowed around 440 intake and better yet in a 2800lb car they went 8.60 1/4 on a less than perfect pass,so i know they make power not just bench no's.
they are fresh with new vlv job,spring height/pressure 240lbs on the seat,ti ret.
75cc's chambers,yes 75cc's on my Aheads and they are not millled down.
13-1 comp with a flattop
old style polished motorsport vlv covers ec.
used msd crank trigger and dist setup.
new meziere water pump and back plate.
also have a frt engine plate for a foxbody and a midplate but never had the midplate installed.
sfi flexplate.
timing cover.
tfs new style tunnelram unported,with dual four top and i just bought the new single top too cause thats what i was gonna use.
also have nos old style fms single four intake.
1150 hp dominator like new.
new accufab coated headers for a foxbody 21/4 pri 4in. collector
it needs oil pump,push rods,main and rod bearings,and rocker girdle and thats about it for parts to be complete.
i hate to sell it but im getting discouraged and need some extra money i live in ohio and im wanting$8000 for all of it.
ill part it out if i get enough guys wanting stuff ,heads need to go first though.
as for pics if your dead serious ill get some of whatever you want to see,weve all seen cranks and rods and stuff before lol!
this engine will easily make over 900hp on the motor n/a
have almost everything to complete it.
DOVE blk soniced,cleaned,billet splayed 4bolt caps,canton main girdle,arp bolts,has been alignbored,needs cyl's bored and honed and decked,have new cam bearings for it too.
new .080 over diamond flattop pistons with upgraded pins.
new .080 over totalseal file fit plasmamoly rings
new grp alum rods 6.800 long.
used crankshaft specialties billet crank 4.5 stroke fresh 20/20 grind has shorter boss snout,has been magged all is good. crank cost $2500 new
new fms damper,i have the short sleeve for the boss snout too.
canton windage tray bolts to the girdle,canton pan, pickup and dipstick for a foxbody.
new custom grind nos cam 289-312.050 825 lift-814. 115sep
nice used set of crane roller lifters,my friend had these so i know theyre good and how long they were used.
fms blue roller rockers and locks
old style fms A-heads ported flowed around 440 intake and better yet in a 2800lb car they went 8.60 1/4 on a less than perfect pass,so i know they make power not just bench no's.
they are fresh with new vlv job,spring height/pressure 240lbs on the seat,ti ret.
75cc's chambers,yes 75cc's on my Aheads and they are not millled down.
13-1 comp with a flattop
old style polished motorsport vlv covers ec.
used msd crank trigger and dist setup.
new meziere water pump and back plate.
also have a frt engine plate for a foxbody and a midplate but never had the midplate installed.
sfi flexplate.
timing cover.
tfs new style tunnelram unported,with dual four top and i just bought the new single top too cause thats what i was gonna use.
also have nos old style fms single four intake.
1150 hp dominator like new.
new accufab coated headers for a foxbody 21/4 pri 4in. collector
it needs oil pump,push rods,main and rod bearings,and rocker girdle and thats about it for parts to be complete.
i hate to sell it but im getting discouraged and need some extra money i live in ohio and im wanting$8000 for all of it.
ill part it out if i get enough guys wanting stuff ,heads need to go first though.
as for pics if your dead serious ill get some of whatever you want to see,weve all seen cranks and rods and stuff before lol!
this engine will easily make over 900hp on the motor n/a