Project: Just an LT1

[dsmawd350]

well the cars hopefully nearing completion/in progress so i figured id start a thread now and try to keep it updated.


About three months ago i headed down to louisvile with trailor in tow to go check out a LT1 trans am

It's a 1993 black with black leather interior, only 74k miles.

the had been forsale for a long time and the price kept getting lower and lower. This is how the car looked a few years ago when it was mint.

http://i7.photobucket.com/albums/y272/amandi01/ta2.jpg

http://i7.photobucket.com/albums/y272/amandi01/ta.jpg
http://i7.photobucket.com/albums/y272/amandi01/547313_3_full-1.jpg

unfortunately the distributor started going out on the car and the owner let it sit and the driveway and begin to go downhill

when i got down to look at it heres how it sat

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=110
http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=111
http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=112

looked like a diamond in the rough to me:bigthumb

so I stole it for $3300 bucks loaded it on the trailor and headed home

for 3300 i got a TA with mint leather int. 74k original miles and heres the mod list:
Mini-Tubbed, narrowed ford 9'' with 3.70's moser 31 spline axles and a tru-trac all with 2k miles on it, 3 Piece FIKSE 18x10 fronts and 18x12 rears, Custom front hubs with tubular control arms, Heimed linked custom tubular rear 4 link trailing arms, Heimed trackrod for rear end. Triangulated front strut bar. brand new CPT pro race 4l60, Yank 3200 stall, Flowmaster 3" Catback with cutout, Carrera aluminum coilovers all the way around, 13" Willwood slotted and drilled with 6 piston calipers for front and 12.5" Willwood slotted and drilled with 4 piston Dynalite style calipers for rear



got home and got it washed up and she cleaned up pretty well, should look good after a full buff and detail

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=115

[dsmawd350]

So, with the distributor going out I pulled it of the trailor and tucked it away in the garage to decide what the plans were going to be.

a couple of weeks went by and i stumbled across a nice loking turbo setup on LS1tech.

went down and met the guy halfway in kentucky

I picked up:

Garret GT42 turbo
hot and cold pipes, cold pipes are polished stainless steel
intercooler
tial bov and tial 44mm wastegate
flowmatched precision 98lb injectors
F.A.S.T. standalone engine management with wideband o2option and 3 bar map sensor.
motor plate
water pump milled 0.25 to account for motor plate


http://www.ls1tech.com/forums/picture.php?albumid=977&pictureid=5416
http://www.ls1tech.com/forums/picture.php?albumid=977&pictureid=6023

[dsmawd350]

next I had to decide if i should run it on the stock motor for a while or do a built motor.

Found a guy up in youngstown ho had a motor sitting in his garage that he bought of his friend tobail him out of a financial situation he was in.

got some details arranged and got the motor payed for. Should be a tough one built with all the best stuff.

-Callies splayed 4 bolt billet caps
-Oliver 5.85 BILLET rods,
-Callies 3.75" crank,
-8.5:1 J&E forced induction pistons
-CC billet 248/248 solid roller custom forced induction cam
-CC solid roller lifters
-AFR CNC competition ported 227 heads with solid roller springs
-Jesel shaft mount rocker arms
-Cloyes billet roller LT1 timing chain
-MSD Probillet distributor
-Ported LT4 Intake converted for use with conventional rear mount distributor
-DRM 58m TB
-MSD crank trigger setup


heres some pics of it with the old setup on it that was going to go ino a C4

http://inlinethumb49.webshots.com/34928/2796471610037773219S500x500Q85.jpg
http://inlinethumb14.webshots.com/1293/2353712730037773219S500x500Q85.jpg
http://inlinethumb59.webshots.com/21114/2996518650037773219S500x500Q85.jpg

[mustanggod93]

that looks like one bad ride

[dsmawd350]

picked up a OEM ws6 hood and some LS1 tails to replace the fogged up and seperating stockers

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=116
http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=117

got some more parts and updates but ill wait till i get pics soon

[chris91]

I always have had a thing for TA's. Those wheels totally set it off too. Good luck with the project!

[5.0calypso93lx]

Damn Chad, looks like a killer setup. LOVE the wheels :bigthumb

Hell the wheels and brakes alone are worth more than what you paid for the car I would think.

[dsmawd350]

Damn Chad, looks like a killer setup. LOVE the wheels :bigthumb

Hell the wheels and brakes alone are worth more than what you paid for the car I would think.

Thanks man! Yeah the wheels alone polished up could sell for close what i gave for the car. Not to mention the wilwoods all the way around, 2300 dollar pro race tranny, narrowed 9", coilovers etc. I could have bought the car and doubled my money as it sat with little effort.

[Rick93coupe]

Dude, what an awesome find. That thing is going to haul the mail too! I'm not a GM guy, but I would have found the money for that car!

[STREETRODZ1]

Definitely a sweet ride, good luck man.

[dsmawd350]

Dude, what an awesome find. That thing is going to haul the mail too! I'm not a GM guy, but I would have found the money for that car!

thanks! should be fun with the 74mm for now.Ill probably do a 91mm over the winter

[5.0calypso93lx]

I'm just a big fan of a bad ass street car, and to me that means some sick wheels with no skinnies in the front, bad ass brakes and a big turbo :D The only thing I'm not to fond of is the auto, even though I know it is faster with it. Sucks that the cold piping is stainless too, but o well, that thing isn't going to notice a few extra lbs from the cold piping :lol:

[dsmawd350]

It may just get a whole new custom kit next year with the 91mm, we'll see what i feel like doing. I'd say the difference in the IC piping would be less than 5lbs changing to aluminum

[Maximus]

It may just get a whole new custom kit next year with the 91mm, we'll see what i feel like doing. I'd say the difference in the IC piping would be less than 5lbs changing to aluminum

DONT DO IT!!!:lol: ;)

[dsmawd350]

loks like my chebby project isnt brewing much interest:(

oh well. got some more pics today. Engine is out, and ill be spending some time tomorrow getting the bay cleaned up and ready for the ABS delete, line lock and wilwood proportioning valve to go in. Then the radiaor support will be getting cut out and replaced with a peice of chromemoly tubing so we can stand my new griffen up vertical for more space. hen the motor goes in :D

ordered my tubular K-member today also, should be here wednesday!

heres the car with the old engine out and the dirty ass bay!

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=120
http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=119

the old boat anchor LT1
http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=121

some of the parts going in soon

madman racing Midplate to go with my front motorplate
http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=124

SJM manufacturing ABS delete kit: wilwood adjustable proportioning valve, pre-formed lines, line lock, toggle switch, remote mounted LED indicator, momentary push button switch,

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=122



i didnt grab any pics of my shiney new Griffen, ill get them when i get pics of the radiator support modding and fab.

[Mustard]

looks like you are making some good progress. Should be a good runner when it's done

[dsmawd350]

Im making good progress ordering parts! Rob@Rigid is the man behind the work

[R825OH]

Thats gonna be a nice ride when you get done. You definitly got a good deal on it!!

[cstreu1026]

Man those are some pretty serious parts engine. Cool project and it should make some serious power when you are done.

[Walter]

Eeeeewwwww, lt1. lol.

[ADaughen]

Oh, look, I have a Blazer in my driveway...

Want to put that LT1 in a Blazer? ;)


Your car looks great. It also appears it is going to run great too.

[dsmawd350]

spent yesterday up at rigid making some more progress on the car helping out where i can. I can't say enough good things about these guys! Can't wait to see the finished product.

When i got there we pushed the car outside and began the task of cleaning up the engine bay. It was nasty.

heres the car with the wiring all bagged up ready to be washed.

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=126

got it all cleaned up and back inside. Next we chopped out the radiator support. you can see the degreased bay in this pic too.

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=127

templates for the plates that will be welded on to cap the support
http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=129

new radiator mocked up
http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=131

next, out comes the heater box off the firewall.
http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=130
http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=132



After the chromoly tube goes in for the radiator support, the motor plate and mid plate brackets get welded in, and the plate gets made for the heater core blockoff. the engine bay is getting scuffed up and repainted with a nice semi-gloss black.
then more work and more pics:D

[Walter]

Coming along real nice!

[STREETRODZ1]

That car is gonna sweet dude, good luck

[2Kblacksleeper]

Very nice build.

John

[85_SS_302_Coupe]

Man those wheels are F'in sick! Almost makes an F body look good (just F'in with ya :D )

[dsmawd350]

more updates and pics to come tonight

[STREETRODZ1]

Ive got alot of love for the f-bodies, that is why i have a 95 camaro waiting for the carbed small block power after the stang is ready. Can not wait to see the new pics man.

[quik lx]

Saw this out at Ridgid this morning...looks like it's coming along nicely!

[dsmawd350]

they got the plate made to block off the HVAC hole in the firewall. gotta figure out how the F.A.S.T and MSD box will be mounted the inside of it it will be painted black

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=140


motor and mid plate are bolted up to the motor and the new motor is sitting in the car on the stock K-member for the brackets to be welded to the frame. Then it's all coming back out to paint the bay, and then it goes back in for good with the Kmember with no motor mounts

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=141


they started laying out the FAST to get it all sorted out and loomed up/etc.

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=139

once again big shout-outs to rob and bill hensley up at Rigid. I wouldnt want the car with anyone else. Amazing detail, and always there to work with you through the whole thing

[dsmawd350]

got the FAST and MSD mounted to the inside of the firewall plate, still need to mount a coil on it and mount the firewall connector for the coil.

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=151

got my tubular K member in

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=150

got the stock k member out and all the suspension taken apart from it to get blasted por-15ed and then go back on the tubular peice

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=145

got pretty much everything mocked up in the engine bay! soon its ready to pull it all back out and paint the bay and begin final assembly

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=149

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=143

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=142

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=146

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=148

[Yellowstang]

thats badass

[juiced347]

nice more progress

[bestracing]

Thats an awesome build there, Why not post it up on an F-body board where more people would appreciate it :bigthumb

[dsmawd350]

got the lower A-arms, sway bar, and spindles all bead blasted and painted with por-15, gonna get up to the shop tomorrow and do the upper tubular a-arms and clean up some brake parts and try to get most of the front suspension back together.

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=185

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=184

gonna get everything all bolted together back in the car before we paint the bay now since the turbo kit needs a few minor adjustments so its taking a little longer than i thought. hope to get it painted and going back together for the final time here soon

[mike94stang]

are you sure you'll be able to handle all that power????? j/k. are you goin w/ a suddle exterior or gettin some crazy paint on it? either way you go, the power your gonna make will back up a wild exterior, good luck, keep updating.

[dsmawd350]

for now im gonna have the oem WS6 hood i picked up painted to match and the whole car 3 stage buffed and waxed etc to get it looking new again. may swap to a 98-02 ws6 front end down the road and have the whole car painted

[5.0calypso93lx]

for now im gonna have the oem WS6 hood i picked up painted to match and the whole car 3 stage buffed and waxed etc to get it looking new again. may swap to a 98-02 ws6 front end down the road and have the whole car painted

Stage 3 huh? Haha j/k. Who is going to be doing the buffing?

[dsmawd350]

Stage 3 huh? Haha j/k. Who is going to be doing the buffing?

3 stage not stage 3:flipoff: LOL
ive talked to plated about doing the whole job, Painting the hood an buffing the whole car out while he has it. I know i dont trust myself with the job:cool2:

[blk93notch]

thats a bada ss car! always loved the trans ams. this might be a silly question but why was the motor converted to the rear mount type dizzy? im just curious as i never saw it.

[dsmawd350]

I dont know how familiar you are with LT1s but they came with the Optispark distributor which is a cam driven dist. located behind and below the waterpump on the front of the block. They cause nothing but problems, the rotor inside is prone to failure at high RPM, as well as moisture being a major problem to them. So im sure you can see how being below the waterpump works out great for them. LOL

[5.0calypso93lx]

3 stage not stage 3:flipoff: LOL
ive talked to plated about doing the whole job, Painting the hood an buffing the whole car out while he has it. I know i dont trust myself with the job:cool2:

I'm considering the same thing that's why I asked haha. After my junk being move around and worked around so much, it's gone a few marks and it never really did get a full wetsanding and buffing so it would really set it off.

[Rich]

Nice looking project! That thing will absolutely fly!!!

[dsmawd350]

got my MSD crank trigger in along with ARP header bolts, ARP balancer bolt, MSD 4253 HVCII coil, and MSD firewall feed through coil connector.

only got pics of the crank trigger.DOH!

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=187

gonna pick a day this weekand get up to rigid with rob and spend an entire day knocking out the last 2 things before the motor can come back out and paint the bay : need to drop the crossover pipe down .5-1" to clear the canton C4 vette pan thats on the car. finish the radiator support and get the griffen mocked up. then its finaly the home stretch, the motor can go back in for good and wire the FAST up and do a few small things like the AN fittings and lines on the waterpump and radiator that are gonna replace the rubber lines and clamps.

[SloRice]

this turd looks slow! :flipoff:

[Maximus]

Any updates?

[dsmawd350]

motor has been in and out of the car getting things mocked up, then to paint the engine bay but it's finally in for good. motor/tranny is in the car for the final time, turbo kit is all heat wrapped and finished and bolted up, suspension is back under the car with the new k-member after it was all pulled out, blasted and i por-15's all of it.

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=209

fuel system is all plumbed and mounted, (not shown in above pic) we pulled the stock tank, sumped it, and welded the -8AN return on top

went with all magnafuel stuff, pump, pre and post filters, 1:1 rising rate boost referance regulator, -10 braided lines for feed, -8 for return

radiator is also in the car and mounted with -16 an bungs for inlet and outlet

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=210

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=212
not alot left to do on the car:
wire up the FAST and all the electronics on the car
build endtanks for my precision core and get that mounted
make the braided lines and hose ends for my coolant system (already have all the -16AN bungs welded on the WP and radiator)
and a few small odds and ends

[dsmawd350]

Finished product: it runs...


http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=348

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=347

[5.0calypso93lx]

How well? :lol:

Looks good man. Has it been on the dyno yet?

[dsmawd350]

no it starts right up and purrs beautifully , but it just has a startup tune on it at the moment.

one of the AN fitting on the radiator is leaking, and a pinhole leak at the fuel sump. once those are fixed (hopefully this weekend) it will be going back to tracey to be street tuned

[Crucial]

damn thats clean, wish mine could look like that lol


keep us up to date on the numbers it puts down... any expectations?

[dsmawd350]

damn thats clean, wish mine could look like that lol




it could....it's just going to cost you :lol:

[bbfstanger]

that looks like a nice clean install,post up some no's!
did you ever get those bad arse rims refinished?

[dsmawd350]

got the fronts done still need to have the rears done and my new tires put on at that time

(hood needs painted)

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=329

345/35/18
http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=321

[JA04GT]

now that is some meat to go under that beast.

[four6trix]

:bigthumb wow, sick ride man

[evil8]

Make sure ya get us some vid. Why isn't this posted on CSS?

[306Power]

Damn those are some meats, I have to admit I do like a clean 4th gen F-body. You think it'll see 450-500 to the wheels?

[Walter]

Damn those are some meats, I have to admit I do like a clean 4th gen F-body. You think it'll see 450-500 to the wheels?

:lol:

[306Power]

Ive seen stock LT1s with turbos make 400 to the flywheel, with his combo my guess would be what 500 HP to the flywheel with some good tuning. So that makes it to what 400-420 RWHP? My bad I was 30 HP off.

[Walter]

Ive seen stock LT1s with turbos make 400 to the flywheel, with his combo my guess would be what 500 HP to the flywheel with some good tuning. So that makes it to what 400-420 RWHP? My bad I was 30 HP off.

:lol:

[Camaro86SHOCKER]

Ive seen stock LT1s with turbos make 400 to the flywheel, with his combo my guess would be what 500 HP to the flywheel with some good tuning. So that makes it to what 400-420 RWHP? My bad I was 30 HP off.

Your just digging yourself deeper, theres too many factors here to determine that, head flow, boost, cam specs and duration, etc...Only the dyno will tell.

Very Clean car though, i like it. However i'm partial to fast F-Bodys :D

[dsmawd350]

HAHAHAHAHA I made 415 rwhp on my last LT1 with a comp cam and ported stock heads. no power adder

this has a fully built motor, not a stock motor with a turbo kit. go back and read the 1st page......

http://www.youtube.com/watch?v=tOKLFF9jTkY

http://www.youtube.com/watch?v=cccYWADbHPw

[dsmawd350]

His Mods:

355 Eagle crank/rod forged low compression custom Ross Pistons
stage 3 ported trickflow heads runner volume is 220cc's
Edelbrock LT4 intake.. unported as of right now (was ina rush to finish up, I will port it soon)
58mm throttle body
224 224 .570/.570 115lsa cam
Comp Promag 1.6's
Stainless steel custom manifolds with 2.5" crossover and 3.5" downpipe (Custom fabbed by me)
Precision PT 78 HPS turbocharger
Tial 44mm wastegate (big and Little blue springs installed)
83lb/hr injectors soon to be 160's
Fuelab 42401 pump (1500hp rated)
all custom rails with -10 feed and -8 return
Aeromotive A1000 Regulator
4" intercooler with 3" intercooler piping (aluminum custom Fabbed by me)
Accel DFI Gen 7 Pro Key w/ DUal Synch Distributor and Wideband


Mine:

383 Callies splayed 4 bolt billet caps, Oliver 5.85 BILLET rods, Callies 3.75" crank, -8.5:1 J&E forced induction pistons
-AFR CNC competition ported 227 heads with solid roller springs -
-ported LT4 intake
-58mm tb
- 248/248 solid roller custom turbo cam
-Jesel shaft mount rocker arms
-tubular headers, 2.5'' crossover, 4'' DP
- Garret GT42 74mm T6 1.01 A/R
-44mm wastegate
-98lb precision injectors
-full Magnaflow fuel system, 2000hp pump, 2k hp regulator, -10 feed, -8 return
-4" Intercooler core, 2.5'' cold piping
-F.A.S.T. standalone with MSD Probillet distributor,MSD crank trigger setup, HVC II coil, and digital 6

[NXcoupe]

That was a super deal you got on that car, and you have done an excellent job with it. Post up the numbers when you get it tuned.

[relaxednoma]

awesome build man, wicked stance and running gear.

so where is the LT1? I have a lame O 4.3 in my 01 sonoma......

[dsmawd350]

where is the LT1? there's an LT1 in it now and the stock one is sold

[5.0calypso93lx]

Is that enough throttle body?

[dsmawd350]

yes, it's two 58mm holes.

like this same thing the guy made 906 rwhp on above ;)
http://www.bfranker.badz28.com/96ss/Port18.JPG

[306Power]

Damn I really must not know my Chevy engines after lookin into it. Guess I should give more credit to them lol.

[NUTTSGT]

Rumor has it this car is getting a chrome-moly 10 pt cage.

[dsmawd350]

haha Who are you?

lol but yeah i posted about it on CSS. It's running and going to Team Z Motorsports the third week of January for a 4130 chromoly 10 pt.

[NUTTSGT]

Somebody posted a link on the Corral. lol You make the trip up to Team Z or buy your tickets through Ron, Badbird?

[dsmawd350]

Yeah i bought them through Ron on yellowbullet

[dsmawd350]

I got some new goodies installed. Strange Pro Series drag brakes, 5/8 stud kit, 15x12 billet specialties street lites with 325/50/15. and 17x7 front runners to clear my wilwood 6 piston brakes. I'll probably end up going strange drag brakes on the front too and going to 15's. or having the 17's narrowed to 4''

also got the interior all torn out. leaving saturdy morning for michigan

http://img.photobucket.com/albums/v611/dsmawd350/325tire.jpg?t=1263702115
http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=40569



when it gets back I'll throw the single plane setup on it along with the PCS digital dash and datalogger and it'll be ready to be tuned :)

[1992MustangDW]

This is one of my favorite builds, and its a chevy

[87stangbbb]

looks like a pontiac to me

[1992MustangDW]

same thing in my eyes, just a very cool one

[87stangbbb]

yeah im just messin with ya. it is a sweet car

[dsmawd350]

This is one of my favorite builds, and its a chevy

Thanks!:bigthumb

[k062693w]

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=40569

:bigthumb That is bad as the F%$K !!! :bigthumb

[9cobra4]

Car looks killer, this will shut the ls1 fags up for a bit I hope. You should tell people its a t25 with a 460 lift cam, that's what cool people with lt1's do anyway. Oh yeah, and stock heads too.

[Camaro86SHOCKER]

very nice, of course im partial to the f-body's. Those wheels look just wicked.

[dsmawd350]

Thanks guys!

[bcoh5gt]

Damn nice build. I hope to catch it out sometime.

[Maximus]

very nice, of course im partial to the f-body's. Those wheels look just wicked.

Yup.

How long is it going to be in Michigan for the cage install??

[dsmawd350]

from the sounds of things just a couple weeks, he said he would have it in and out for me

[Maximus]

from the sounds of things just a couple weeks, he said he would have it in and out for me

Damn.:eek:

[dsmawd350]

I doubt he wants to have a car he is doing for free sitting around taking up garage space

[Maximus]

I doubt he wants to have a car he is doing for free sitting around taking up garage space

Didnt you buy a raffle ticket or something?

[dsmawd350]

yeah Team Z agreed to do a charity raffle for the cage.

[motox159]

Going to be one sick ride.....Nice

[bascom123]

Thats one sexy firechicken.. i love mine and wish someday to do a LS3 swap..

[dsmawd350]

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53005

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53010

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53009

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53011

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53006

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53008

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53007

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53012

[Buckeye]

Did you get rid of the wheels? they where the best part

[dsmawd350]

oh where they? yes i sold them

[Walter]

Get it done!

[cobra429boss]

I like the wheels that are in your pics you posted .. Def a bad ass car.. Looks BADASS

[draggin50]

I've never been a big fan of the F-Body cars but this could turn me!!! Looks bad ass. Thats a nice looking job on the cage. Keep the pictures coming!

[dsmawd350]

decided to work on it some more :ty:

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53748

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53749

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53750

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53751


dennys nitrous ready chromoly driveshaft

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53747

racecraft steering shaft setup

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53746

pinto manual rack

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=53745

http://www.cincystreetscene.com/forums/picture.php?albumid=14&pictureid=490

got my tunnel mount adjustable torque arm on.

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=54037

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=54036

big thanks to OldBlu and his buddy for a killer deal on a brand new never even bolted up TA

[dsmawd350]

Got my shifter installed finnally along with the linkage and cable all set up properly. This was probably the biggest pain in my ass on the whole car due to shitty instructions from B&M and a shifter thats made to fit like 10 different transmissions with pulling a pin here, adding a pin there, this bracket for this, spacers for this no spacers if its this. Finnaly got it all figured out with enough trial and error.

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=54035

got the piping all changed up to fit the new setup, fuel rails and lines all bolted up. just need to mount the map sensor somehwere now and run a vaccuum line to it as there is no longer a provision in the manifold itself.

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=54033

http://www.ls1tech.com/forums/picture.php?albumid=13879&pictureid=54034


whats left: relocate coil and extend wires, install oil pressure sensor, and start t00ning!

[Walter]

Looks good for a chebby!

[dsmawd350]

well been through a lot of changes. getting close now

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/307431_10150767252470462_511620461_20358881_106764 3_n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc7/308915_10150767252180462_511620461_20358874_255651 8_n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc7/316196_10150768476010462_511620461_20374260_161916 _n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/303288_10150768476115462_511620461_20374263_760519 7_n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc7/307223_10150768476390462_511620461_20374270_113324 7_n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc7/303711_10150771485080462_511620461_20404634_690207 0_n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc7/298526_10150771485490462_511620461_20404639_219094 8_n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/297841_10150771576435462_511620461_20405507_186486 _n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc7/314059_10150772492780462_511620461_20414296_125169 9_n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc7/320476_10150772331760462_511620461_20412940_619927 4_n.jpg

[dsmawd350]

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/317460_10150780700310462_511620461_20507784_157776 814_n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc7/297365_10150784499175462_511620461_20533895_593200 297_n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/317074_10150784499705462_511620461_20533898_106984 599_n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/308760_10150784499735462_511620461_20533899_692486 457_n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc7/303131_10150790644955462_511620461_20592103_181614 130_n.jpg

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/321340_10150790645075462_511620461_20592106_163313 9724_n.jpg


painted and all back together..

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/315518_10150790931770462_511620461_20595149_664679 155_n.jpg

[Moody]

its looking good.

[Whyucryn]

So is this thing ever going to be finished or what??

[V8Mustang1967]

That is one mean bisch!

[mustang_gt88]

nice project

[dsmawd350]

Its finished now, just gotta build a downpipe and its done

[orangedemon331]

Its never gonna be done! Now its time to start a whole new set of problems! Thats how this game works!! But it looks good! Now get it out of the way so i can get my car in there!!!:flipoff:

[Maximus]

Its finished now, just gotta build a downpipe and its done

Chuckles and his NOS are waiting for ya.


Its never gonna be done! Now its time to start a whole new set of problems! Thats how this game works!! But it looks good! Now get it out of the way so i can get my car in there!!!:flipoff:

Storage??:lol:

[bkstang95]

Updates??

We have to race our unicorns at least once before snow falls! :lol:

[dsmawd350]

headed to Cincy Speed wednesday!

[JASON408]

looking good man !!hope to see it at the track soon

[orangedemon331]

Glad this thing is done, im getting tired of pushing it around Rob's shop, dammit i wanna push my own around the shop for a while!! :lol: