93 Coupe Project"Neighbours Nightmare"

[AZZKIKR]

A little while ago I rescued a 93 coupe that was going to the scrap yard.I live in Canada.Alot of our cars here are junk.(rusty)I have some good friends in New Hampshire.They are into the mustang scene pretty hard.They called me and told me about this car.It is a 4 banger car with a black gut.:)Just what I was looking for to build my next ride.I have an 83 coupe now that has seen better days.It was run for years with a BB 460 in it and was never frame connected and was twisted up alot.This car has a 351 and a stick in it now and runs 11.7 on motor and 11.1@126 on the hurt(nos).The only thing that is bad on this 93 is that someone that owned the car before me put an aftermarket sunroof in it.:mad:So I will be roof skinning the car.Also the rad support is not the greatest so that will be swapped also.As soon as I figure out how to get some pics on here I will post them up to show the progress.I have to get this car finished so I can get to work on a 93 hatch that my wife brought from the states also.She has a 91 hatch now that has gone 12.7 in the 1/4.It has a 302 with a stick.Well gotta get to work on the coupe.:chug:

[AZZKIKR]

trying to load pics

[AZZKIKR]

Putting the car up on a rotissarie.I am a little lazy after all these years of beating on mustangs.My body can't take lying on the ground anymore.A little scary at times getting the car up on but well worth it.Once the work is done I just have to figure out how to get the car back on the ground.:D

[AZZKIKR]

Here is some pics of me sandblasting the underside of the piece of crap.That's a rotten job.:flipoff:I just have one more session with the blaster and then it is done.Need to finish taking the wiring harness out of the engine compartment and a few other things and I can blast it.

[AZZKIKR]

Installed torque box re-inforcements.

[AZZKIKR]

Here is some pics after welding the torque boxes and etch primer.

[Goober]

Good work! That takes a lot of dedication to save one from the crusher!

[Mustard]

Good work! That takes a lot of dedication to save one from the crusher!

hell yeah. we need more people to do this.

[may93]

Looks good and I like the rotisary. I've actually considerd building one myself. My project is a coupe also.

[AZZKIKR]

yes,may 93 I looked at yours on here and the car is coming along nicely.good work

[AZZKIKR]

I have had a few people ask how the rotisary was built so here is a few pics.

[AZZKIKR]

some more pics

[AZZKIKR]

I am getting to the point that I need a cage.From your guys experience who makes the best and easiest cage to install?I was thinking of wolfe or wild rides but not sure.Thanks.

[91boost]

Nice work:bigthumb

[Rick93coupe]

My vote would be for the wolfe cage, I've looked at several of them, and as far as mail order cages go, they're top notch.

[PaulFiveOh]

Outstanding work. Eh?

[graysonracin]

Nice work, keep saving those stangs!:bigthumb

[AZZKIKR]

Just picked up an 86 GT that is super clean...This will be my next project when I get this one finished.Into the race season here hard so everything is on hold for now.Trying to get ready for the world street car race...I will get some more pics up soon.

[DeckerEnt]

Great work on your coupe. Mine is coming along as well. Good luck with it and keep it up.
Keith

[jfiscus]

I am getting to the point that I need a cage.From your guys experience who makes the best and easiest cage to install?I was thinking of wolfe or wild rides but not sure.Thanks.

I have heard great things about SW Race Cars & their cages, but my buddys' experience is with their cages for Jeeps:
http://www.swracecars.com/corp/roll_bars.asp

[AZZKIKR]

Thanks for all the info.I have to get to work on the coupe soon as I want to have this thing ready for the track in the spring.I need to retire my old 83 coupe soon.I finally hit the 10's with it last time at the track.It's getting a little twisted,as it is a stick car...LOL Thanks again.

[AZZKIKR]

Finally got a cage ordered from wolfe racecraft, 10 pt cromoly,coil over shock bar,window net kit,heater bar,through firewall bars,through floors and mini-tubs. Can anyone suggest to me a good place to get a narrowed housing?What are the dimensions to ask for and also what back spacing for the wheels should I be looking for.I am going with a 325/50/15 drag radial...Thanks much appreciated

[Sharad]

sweet project dude! Love the rotisserie.

[4barrel]

Holy back from the dead thread, Batman!

[AZZKIKR]

Hopefully will make some progress soon...will post pics as it takes place...

[ibstrokin]

Stock wheel wells will hold a 15x10 w/6.5"b.s., I think you can narrow by about 1.75", which would bring your b.s. to 4.75". You may want to consider using 9" ends, that will keep you from using c-clip eliminator's. Moser should be able to handle the narrowing, or a local fabricating shop, check with hot rodders in your area. Cool project.

[ibstrokin]

You will probably need to trim the lip in your wheel well also, you may want to do that before paint.

[4barrel]

You will probably need to trim the lip in your wheel well also, you may want to do that before paint.


The rear end setup in my car is real similar to this. Narrowed 1.5 inches, with a 15x10 with a 5.5 back space. Instead of trimming the wheel well lip, it was rolled.

[AZZKIKR]

Thanks for the info guys...the cage,wheel tubs,etc. will be here shortly.Time is the issue now.As long as I can stay away from sledding this year I will make good progress on this project.Thanks again. Oh by the way who makes the best disc brakes. I know there might be mixed opinions on this but what have you guys learned and had good luck with?

[AZZKIKR]

Started the through floors tonight...have pics soon.Finally getting back at it...

[draggin50]

Thats a good looking job you have done. Makes me want to get a coupe and try one like that. Keep it up!

[AZZKIKR]

Got the drivers side done on the weekend...

[AZZKIKR]

Well i finished the passengers side through floor tonight...now the debate whether to start the cage or do the mini-tubs next.Would like to do the cage but I think it would be easier to do the mini-tubs before the cage.Figured out a few more things on the engine combo today.Bought a set of heads,cam,intake,headers and possibly crank and a set of rods... does anyone know how far an 351w based svo block can be bored safely? It is 40over now but needs to go more to match a set of pistons I have a chance to get. Thanks.

[AZZKIKR]

Well I got one mini-tub in this weekend and started cutting out the other wheel well.Alot of screwing around doing those when you have no idea what you're doing...lol...picked up my kooks headers 2" primary and 3 1/2" collector.Brodix/Neal cylinder heads,intake to match,T&D shaft mount rockers,cam,lifters,and ordered a set of CP pistons.Thats about it for now and I will get some pics up this week of the mini-tubs.Hope to have it done this week.After this will be the cage...

[NXcoupe]

As for disk brakes, I am sold on aerospace brakes. I have them on both my race cars. They are priced well and work great. As for svo block, have it sonic tested, then make your decision on how far to bore it. Costs a little but well worth the investment considering the alternatives.

[AZZKIKR]

Thanks for the info.Much appreciated.Ran into a major set back today with the block(9.2 deck)and the other stuff I have here is for a 9.5 deck.I don't know much about engines as far as building them so this is a learning lesson for me.I have the problem solved but it cost a few bucks.Man-o-war block will fix it.The engine will now be a 427 cuin engine.

[NXcoupe]

wow, yeah, that will fix it, lol. Wish you lived closer! lol.

[AZZKIKR]

Here is a few pics of the mini-tub process and the Kooks headers...and yeah I wish you guys were closer to me too as it would help me stay focused on building the car.Sometimes it's hard to stay on track.I have some great friends from(NH and CT)that helped me strip the car down but again they are a ways away.One good thing I have going here is my wife drag races too so she helps me out here and there and she understands this DISEASE...lol...if you guys see anything here I am doing wrong let me know as I need all the help I can get.I want to certify the car sometime to 8.50. Thanks.

[AZZKIKR]

More pics...

[chadomac]

very nice

[AZZKIKR]

Thanks,more pics soon...I am still doing the mini-tubs.Cage will be next...

[grntrunk]

juuuuuuunk!!!!:flipoff:

looks good J

[AZZKIKR]

Finished the pass side mini-tub tonight.Just a few minutes of grinding and all is good.Will post a pic soon.Now onto the cage.

[Blackout50]

Damn Jason wish I had 1/10th your ambition.

[AZZKIKR]

Thanks guys...here are a few more pics.Mini-tubs are done finally and started fitting the cage.Today I got hooked up with the use of a tig welder.Should be here in the garage this week so I can start tacking the cage in place.Now I just have to teach myself how to use it.

[AZZKIKR]

And a few more... I am ordering a set of Mickey Thompson DR this week to check fitment.I am going to be getting a set of 15x12 wheels sometime and the tires I am using are a 325/50/15.Does anyone know the measurements for the rearend? I am going to call strange here soon or if anyone knows where I can get a housing that is narrowed,complete or even bare that they want to sell let me know as I am in need of one.Would like to find one that has the wheelie bar,anti-roll and coil over brackets welded on.Thanks.

[Blackout50]

J I have housings get me the measuements and I can have one done. These guys are the next town over http://www.jwracing-fab.com/. $225 narrowed with 9" ends.

[AZZKIKR]

Not much done tonight,but i did take out the non-factory sunroof.
:mad: I will be roof skinning this thing to fill the old hole.Alot of work but want it done right or somewhat.lol

[DeckerEnt]

Jesse skinned a roof on his. Turned out pretty well. Stangman on here!!

[may93]

I need to finish the car Im doing for someone else and then get busy on mine. I bought the mini tubs but havent started yet. I'm planning on running a 12 inch rim with a 3 inch offset. Having 2 teenage drivers with one in college definitely slowed the car funds down. I gotta find a rotisary though. Yours is looking good. Very similiar to my coupe. :bigthumb

[AZZKIKR]

Thanks Chris,I will get it sorted out then shoot you some measurements.I may have to send you my anti-roll bar tabs and shock brackets so they can be welded on too.While I am at it I may get a set of wheelie bar brackets also.Thinking the rear will be shortened 2" on each side and using 9" ends as you mentioned and setting up for disc brakes too.I got the tig welder tonight and I just need to get a plug for my 220 outlet,tungsten tips and some rods so i can get at it.Also notched the seat brackets for the rocker bars tonight.Thats about it for now.

[black90lx]

looks good. i'm glad your taking your time and doing it right and posting pics. good build thread...:bigthumb

[AZZKIKR]

Thanks...just hoping these pics can help other people out a little.

[AZZKIKR]

Tonight I got the tig wired up and started playing around with it.Very nice to work with compared to a mig.Hope to start tacking the cage together tomorrow night.Pics soon.

[grntrunk]

looks sick J, nice work. nice thing about having to remove the roof is that you will be able to get excellent welds on the top of the cage. :cool1:

[AZZKIKR]

Got some of the cage tacked in place last night.Slow going as I am still trying to get a handle on using a tig.Going to put in the rear bars today and figure out where to cut for the through fire wall bars.

[AZZKIKR]

Thanks Saul...just think soon we will be in Bradenton,FL at the springbreak shootout!!!Today I got the holes cut for the rear bars to go through the package tray.Had to square the main part of the cage and got it tigged to the floor.Little bit of a bitch but it's pretty well perfect.Hope to get the rear bars welded in and one rocker bar as they sent me only one...anyway I have a piece of moly tube coming for the other side this week.Should be able to get the door bar in too and fit the through fire wall bars too tomorrow or should I say later today...lol...thats it for now.

[AZZKIKR]

Little more done...

[grntrunk]

Thanks Saul...just think soon we will be in Bradenton,FL at the springbreak shootout!!!

I can't wait dude.

[Blackout50]

Gotta love the empty cases of BL and Alpine...Was that a weekends worth?

[AZZKIKR]

Cage is almost finished...just the through fire wall bars left to do...thank f$#k...lol

[dsmawd350]

im probably late but if you were asking stck 8.8 length it is 54 1/8 flange to flange

[AZZKIKR]

thanks dsmawd350 as it saves me digging one out of the snow to check it...haha. I am going to shorten the axle 2.5" on each side. With a 15x12 wheel I will be using a 6.5 back space wheel.Think I may go with a set of Billet Specialties street lites.My drag radials will be in this week so they tell me.I also bought a few other things today.An Aeromotive A2000 fuel pump,2 regulators and fuel log,6AL and a 2 step,digital retard box,NOS launcher with touch screen...going to order a fuel cell this week.Hope to finish tigging the cage this weekend and start at the engine compartment...

[dsmawd350]

sweet man! i would like to pick up a virgin coupe roller here eventually and slowly do a build up on it. minitub, fab 9 etc etc etc etc hahah
Good choice on the wheels. I am running a BS street lite right now in 15x12 with a 5.5 backspace. and a MT 325 radial.

[AZZKIKR]

Few more pics...not much progress as my business is getting in my way right now...lol

[AZZKIKR]

Few other things I picked up lately... Power master 1 wire alternator,drag radials,QA1 front struts, anti-roll bar and coil over rear shock bar...

[AZZKIKR]

Heading to Bradenton Florida.Hope to find some more parts...

[AZZKIKR]

Well made it back from florida...was a great trip.Love the true street class.There was a guy there that ran an 8.17@177...wow. Went to the gatornationals too. Well hope to have more pics soon as i am going back at it...

[AZZKIKR]

Engine is done... 427 cu in.

[AZZKIKR]

Working on filling holes in engine bay now...

[Blackout50]

So J you gonna run 2 T5s in series or side by side behind that beast?

[AZZKIKR]

LOL... i wish i was still running stick in this thing but looking like it will be a glide. Ordered a 9" rear today from dave at Team Z Motorsports. 9" will be backbraced,40 spline,gun drilled and star flanged axles,pro gear 3.70,strange brakes,etc... should be a nice piece.Debating on what to use for wheels now as it looks like the wheels i was looking at are heavy especially when they're beadlocked.Lately i have been working on the engine bay.I will post pics soon...

[AZZKIKR]

Almost done the engine bay. Had to replace a bent piece on the driver side ahead of the strut tower. Got the window net in too.

[AZZKIKR]

Got a fuel pump, 5 gal fuel cell and radiator...

[silver_notch138]

J, I might have a meziere electric water pump for sale. used the same amount as the rest of the stuff you got from me. My blower pulley won't clear it so thinking it is up for sale now.
That stuff looks good, nice work. I think that engine would like two kits on it.....

[AZZKIKR]

Thanks man, i will be in touch with you...thanks for the heads up.

[grntrunk]

Where do you get the energy!? I thought you said you were gonna stop spending for a little bit when i spoke with you like 2 or 3 weeks ago:lol:

Looks good dude. :cool1:

[Blackout50]

So youi didnt go with the race C/C plates?

[AZZKIKR]

I have both cc plates here...i will be using the race plates when it's time but I am a long ways away from that...:( I will get it sometime,depends on time and money. How you guys making out with your cars?

[AZZKIKR]

Energy, what's that. If I had energy I would have alot more done. I need to get this done so I can get my lovely wife's car done...lol

[93RedNotch]

Nice build, really diggin the bb notch....

[Blackout50]

I have both cc plates here...i will be using the race plates when it's time but I am a long ways away from that...:( I will get it sometime,depends on time and money. How you guys making out with your cars?

Looks like you are single handedly trying to stimulate the US economy with your project. :lol:
The blue coupe is getting there.I bought a 93 Cobra motor with 44k on it that will be going in it .Last night I did the floor hump for the 5spd . Im moving into a new shop over the month of may so it may slow me down a bit but hopes are to have it driving by then. I will still have more things to go back and do the way I wanted to but time and $$ is an issue as always.

Oh !! I bought another Fairmont too...

[TooFast98Cobra]

looks great man, wish I had the motivation to get my project done that you have.

[AZZKIKR]

Nice build, really diggin the bb notch....

Actually it's a small block...lol

[AZZKIKR]

Looks like you are single handedly trying to stimulate the US economy with your project. :lol:
The blue coupe is getting there.I bought a 93 Cobra motor with 44k on it that will be going in it .Last night I did the floor hump for the 5spd . Im moving into a new shop over the month of may so it may slow me down a bit but hopes are to have it driving by then. I will still have more things to go back and do the way I wanted to but time and $$ is an issue as always.

Oh !! I bought another Fairmont too...

Do you need a hand to move? I will make the trip down to give you a hand man.Let me know... Fairmont...pics please...lol... is it a wagon with wood grain?

[AZZKIKR]

looks great man, wish I had the motivation to get my project done that you have.

Thanks, the motivation is all the coin I have spent so far.I rolled for years with junk yard parts and had good luck but now it's time to step up a notch...:D

[93RedNotch]

Actually it's a small block...lol

I still really like it. lmao

[AZZKIKR]

Thanks 93rednotch... it's alot of work for me but it will be worth it I hope.

[93RedNotch]

Thanks 93rednotch... it's alot of work for me but it will be worth it I hope.

It will be. I have yet to see a notch above 400 ci that isnt nasty. Good Luck :bigthumb

[AZZKIKR]

Thanks,should work alright...here are the engine specs:
427ci World Products Block
12.5:1 compression Ratio
4.00" Scat Pro Comp Forged Crank Internally Balanced
6.200" Scat Rods with ARP 2000 Bolts
CP Custom Flat Top Nitrous Pistons
Brodix Neal BF 201 Heads
2.125 Ferrea Titanium Intake valves
1.600 Ferrea Superalloy Exaust Valves
T&D Machine 1.7 Shaft mount rockers
Crower Solid Roller Lifters
Bullet Racing Camshaft .800/.765 lift
Edelbrock 2863 Intake
Should handle a fogger with a 300 shot.

[draggin50]

Thanks,should work alright...here are the engine specs:
427ci World Products Block
12.5:1 compression Ratio
4.00" Scat Pro Comp Forged Crank Internally Balanced
6.200" Scat Rods with ARP 2000 Bolts
CP Custom Flat Top Nitrous Pistons
Brodix Neal BF 201 Heads
2.125 Ferrea Titanium Intake valves
1.600 Ferrea Superalloy Exaust Valves
T&D Machine 1.7 Shaft mount rockers
Crower Solid Roller Lifters
Bullet Racing Camshaft .800/.765 lift
Edelbrock 2863 Intake
Should handle a fogger with a 300 shot.

Damn sounds nasty!!! Should run real good!

[silver_notch138]

Should handle a fogger with a 300 shot.
Should handle two 300 Kits with no problems.

[AZZKIKR]

I will need two kits to keep up to you Adam...lol... your engine looks nasty and it will be! CFE are a nice head :)

[Blackout50]

Here is a pic of the 90 as it sits now.http://i261.photobucket.com/albums/ii62/blackout50/nightattheshop006.jpg

[Blackout50]

and the engine that I just bought with 44k on it.http://i261.photobucket.com/albums/ii62/blackout50/cobramotor002.jpg

Yep its a legit 93 Cobra motor.

[AZZKIKR]

Thats awsome man, good to see the blue coupe is coming together. Very nice, that car looks super clean. I am still filling holes in the engine bay...taking my time.Hard to get any progress with an hour at a time,things are going to be very busy this year so things will be slow going that's forsure.Oh well it will be done someday...

[Blackout50]

Yeah it has only 47k on the car. some rot on the left rear frame rail where the tailpipe was rotted off and accelerated the rust about a 4" section.I have the cut-out from another one and will address it down the road.

[Blackout50]

When I bought it almost 2yrs ago.

http://i261.photobucket.com/albums/ii62/blackout50/25001.jpg

[Mustard]

thats a great build you got going man keep it up

[AZZKIKR]

Well got a few more parts this week. Picked up a 1050 dominator pretty well new, only had a few tanks of fuel run through it. Also got a menzerie electric water pump (thanks silver_notch138). Got a new Harwood 6 inch extended cowl hood... finished with the engine bay for now. Time to move to the rear of car to get the trunk cut out. Pics soon...

[grntrunk]

I drove my mustang today. It felt great. Was playing around with the tune.
It runs real well. Safe under boost right now. More to play with and learn but my dumbass can only take so much ;)

[AZZKIKR]

Awsome man, nice to see you getting some use out of that car unlike myself with them just sitting around. I got the trunk area cut out today...pics soon. Saul post a pic of your car!!! That's a nice ride...

[AZZKIKR]

Picked up a carb this weekend and got the trunk area ready to build...

[grntrunk]

Awsome man, nice to see you getting some use out of that car unlike myself with them just sitting around. I got the trunk area cut out today...pics soon. Saul post a pic of your car!!! That's a nice ride...

My car sat for a long ass time. It drove me nuts.

Good to see you are making some progress!!

[AZZKIKR]

Slow going but I'm not quitting till this thing is done this time...:lol: For some reason I can't load pics anymore. My browse button for the attachments is missing.

[Stangman]

Slow going but I'm not quitting till this thing is done this time...:lol: For some reason I can't load pics anymore. My browse button for the attachments is missing.

Because of site maintainence. Just link from photobucket

[AZZKIKR]

1050 dominator...more pics soon as i need to figure out photobucket..lol

[grntrunk]

that looks pussy :flipoff:

[AZZKIKR]

I got my 9" housing from Team Z Motorsports and it looks great!!! Also picked up the front brakes too and master cylinder. More pics soon...

[silver_notch138]

Nice work Jason. Can't wait to see that thing rip off some quick times..

[AZZKIKR]

Here are a few pics of the 9" housing from strange and team z motorsports... I can't wait either Adam. Thanks for your help with this project!

[AZZKIKR]

Trunk area cut out...

[Blackout50]

My J you have quite a nice rear!

[Blackout50]

Have you taken the old grey whore to the tarck at all this year?

[grntrunk]

you crazy bastard!! That looks great man. wish i could join in on the fun.

[AZZKIKR]

The old grey car is heading for a "hot supper" soon.Just need to get the new clutch and sfi bell in from APW before I head up...you guys need to come up sometime and we will take turns banging the gears out of her.

[Blackout50]

Throw a few more bars in it and its starting to look like a SSO car.

[Blackout50]

The old grey car is heading for a "hot supper" soon.Just need to get the new clutch and sfi bell in from APW before I head up...you guys need to come up sometime and we will take turns banging the gears out of her.

J call me tonight.

[AZZKIKR]

I will give you a call later in the evening.I think I am going to get in touch with Wolfe RaceCraft and order the funny car cage part...not really sure but we will see

[AZZKIKR]

Finally got the rear housing up in place tonight thanks to my friends, otherwise it would still be sitting in a box. Now to figure out the shock length and where to mount the shock bar and anti-roll bar...

[AZZKIKR]

A few pics of testing the housing in the car. I borrowed a set of rims and tires to check the back spacing.Hope to order rims soon.With these wheels there is lots of room on the inside and I just have to trim the wheel well lips a little.

[Blackout50]

I think its gonna be a little stiff with those wood blocks...

Ohhhh and what wheels are these?

[AZZKIKR]

American Racing, 15x12 with 6" BS. I think I am going to see if I can get 61/4" BS so I don't have to do much to the wheel well lips. Going to call them tomorrow. Team Z Motorsports told me 6-61/2" will work. These wheels look really good on there but I have to cut around 3/8" off the lips...

[Blackout50]

Just roll the lip. I have it done one both of mine and you cane even tell.

[AZZKIKR]

Did you use the tool to roll the lips?

[Blackout50]

My body guy did it by hand.

[AZZKIKR]

Well, I can't take it anymore. Off to the track with my old '83 coupe. I was hoping to sit this year out and save money for this project but I have to get some frustration out...lol... maybe it will motivate me a little too...

[Blackout50]

Did you go?

[AZZKIKR]

We went ran an 11.68@117. Has been 11.47 on motor and 10.72 on 125 shot.Made 5 passes with it rattling. Won 3rd in my class. Set the valves and the noise was still there. I think it's a rod bearing.Oh well not bad for 7 years of torture,always with a stick and has had alot of nitrous ran through it(25-30 bottles) lol. Question is now to rebearing the 351w and change the cast pistons to forged or build a stroker for it... We will see as I am still debating. I don't want to pull funds from the 93 project car. I am leaning towards a 392 with the canfield heads but that means headers,solid roller cam,etc...I don't think the chassis is going to handle it though.Decisions,decisions...I will post what I decide to do and a few pics.

[AZZKIKR]

Well been awhile since I have posted on here so here's an update. Ended up freshening the 351w. Had to use another block as the original one was cracked up the middle. Put it back together with the same combo. Car ran good until I broke the G-Force t-5. I have parked that car. We made a trip to the shakedown and watched that race and had a great time. I ended up buying a car down there as I am not going to have time to get this 93 coupe ready for this coming race season. Picked up a stock suspension drag radial 99 GT,4.6 with a TCI ProX glide. Runs on 275 radials. Nice car. I will post pics sometime. Does anyone know what is involved to get a liscence to race in the U.S.??? Thanks. Might come down and try a few X275 races this coming year.

[AZZKIKR]

New Car.

[bbfstanger]

hell yeah looks nice!

[jack90gt]

Holy shit that is badass.....

[AZZKIKR]

Thanks guys, it's coming along. It has a 4.6 with an F1R Procharger. TCI Pro-x glide. Complete stock suspension car, no mini-tubs. I have 325/50/15 DR's on it now but was run with 275's. Thought I would use the 325's to learn on for starters.Should be fun. I have alot to learn...

[93RedNotch]

Holy shit that is badass.....

lol what he said!!! that things nasty! vids in the spring?

[AZZKIKR]

Sure thing, i will post em up. Just waiting patiently or trying to...lol

[jack90gt]

How many lbs. of bosst? isnt the f1r up there????

[AZZKIKR]

Yes it is... Lots of boost.HaHa

[2000GT]

that is sweet!!!!!!!!!!!!!

[JROUTLAW331]

Sweet car dude.....luv the color!!!

[AZZKIKR]

Under the hood shot. Just a little 4.6 4V motor...lol

[draggin50]

Damn that is a sweet ass car! Should be pretty nasty!!!

[TooFast98Cobra]

lookin good, what brand hood is that? gear driven also I see?

[AZZKIKR]

Yes it is gear driven.Gear drive from the supercharger store. I forget the name of hood but I will check and see next time I go wrench on it.

[5.0calypso93lx]

What coil packs are those?

[AZZKIKR]

The hood is made by VFN and the coils are gm. Hope to get out testing soon.Sent the hood out to get repaired as it had a chip in the corner and a few spider web cracks from it blowing onto the ground from the previous owner.Should be fun as long as it stays together.

[AZZKIKR]

Well hard to believe but it's been over 2 years since I have done anything with this project...see how much I get done this winter...worked on it this past week in evenings and got anti-roll bar in and shock bar...etc

[331lx]

Looks sick

[AZZKIKR]

Few more things put together...test fitting some front end parts

[331lx]

Nice progress man

[AZZKIKR]

Thanks 331lx! Going to call Team Z for some more parts this week (tubular rad support, travel limiters,motor/mid plate kit) also Scott Rod Fab to get a trunk panel and maybe a rear seat delete kit. May also look into a set of V Series spindle mount wheels and spindles/brake kit etc for my '99 Stang and use the alumistar 2.0 off that car on this coupe...see what happens

[90fastgt]

Nice progress looks nasty

[331lx]

This car is nasty looking

[adragon72]

great project!!!!!

[draggin50]

Glad to see ya back on this one Jason! I know the other car is bad ass for sure!

[AZZKIKR]

Thanks guys, trying to stay at it this winter. Just have to make sure it's not faster as my wife has laid claim to it!

[Maximus]

Keep the pics coming!:bigthumb

[AZZKIKR]

She's a roller finally...hope to pick up some parts shortly from Scott Rod and Team Z. I have ordered a bunch of stuff. Now I have to find a tranny...that won't be cheap! LOL

[331lx]

I love this build

[2Fast4You]

She's a roller finally...hope to pick up some parts shortly from Scott Rod and Team Z. I have ordered a bunch of stuff. Now I have to find a tranny...that won't be cheap! LOL

What trans are you going to use?

[AZZKIKR]

Well I've had great luck with my TCI Pro X glide in my other car so I am thinking of getting one of those, just built a little better and do a swap so the better tranny is in the blower car and the other in this build... unless I find a deal somewhere...see what happens